Cangzhou, Hebei, China
Response Time: < 24h
Response Rate: 100%
| Model No.: 1200*2400 | Place of Origin: China |
|
Model |
GYKM1250x2400 |
|
Max. speed |
150pieces/min |
|
Economic working speed |
100-120 pieces/min |
|
Minimum sheet feeding size (mm) |
400*700 |
|
Maximum sheet size for continuous feeding(mm): |
1250*2400 |
|
Maximum printing area (mm): |
1250*2200 |
|
Wall to wall distance(mm): |
2600 |
|
Range of printing plate thickness(mm): |
6 |
|
Sheet thickness range(mm): |
2-11 |
|
Slotting accuracy(mm): |
±1.5 |
|
Machine body thickness |
50 mm |
|
Motor voltage |
440V |
|
Printing roller dia. (mm): |
410 |
|
Anilox roller dia.(mm): |
213 |
|
Rubber roller dia.(mm): |
198 |
1. Feeding part one unit
2. Printing part two units
3. Slotting part one unit
4. Die-cutting part one unit
Totally 5 units.
Unit moving.
Each unit is electric moving left and right with warning bell. When unit moving, the bell will be warning to make sure the operator safe. The moving motor with constant torsional moment which can buffer the impact of the two units when the operation is wrong.
After all the units closed, each part is pneumatic locked. There is also lead locked cylinder which can make each part locked with bottom-track lock. If the cylinder is not locked, the main motor will not work.
Lead-edge feeding system.
Wind absorbing auxiliary paperboard feeding, can make the cardboard feed favoringly. The volume of the wind can be adjusted accord the camber of the paperboard.
Electric control the side baffles move left and right. Electric control the behind baffles move back and front. The distance between the frontal baffles and the feed table is synchronous manual adjusted.
The touch screen can be input the production plan and also show the produce sheets number. Once the plan is finished, the system stops the feeding part and warns.
Dust clean.
Brush dust-removal equipment with dust-absorption blower. This equipment can clear the dust on the surface of the cardboard, improve the printing quality.
Cardboard feeding roller.
The up cardboard feeding roller is steel tube , be covered with the hardwearing rubber.
The down cardboard feeding roller is steel tube embossing and hard chromium plating.
The distance between the up cardboard feeding roller and down cardboard feeding roller is adjusted by hands, while the dial show the adjust date, the adjusting scope is 2-12mm.The up and down feed roller adopt the crosshead connect with the drive gears, when adjust the distance between the up and down rollers, the distance between the two driver gears of the up and down rollers will not changed.
The printing roller
The printing roller is steel material, after balance correction and grinded, polished and hard chromium plating.
The printing-plate-reel / plate hang-up structure is adopted. The pedal switch control the printing roller run clockwise and anticlockwise, can change printing plate easy.
The down press printing roller.
The down press printing roller adopts seamless steel tube , after balance correction.
The surface of the down press printing roller is grinded, polished and hard chromium plating.
The distance between the printing roller and down press printing roller is adjusted by hands wheel, while the dial show the adjust date, the adjusting scope is 2-12mm.The printing and down press printing roller adopt the crosshead connect with the drive gears, when adjust the distance between the two rollers, the distance between the two driver gears of the two rollers will not changed, ensure the high precision for the carton, and low noise of the machine, and long life of the gears.
The anilox roller
The material of the anilox roller is steel, usually choose 220# 250# .
The steel anilox roller surface adopts advanced chromium plating. Smoothness and hard wearing.
The Pneumatic control Up-down device of the anilox roller is synchronous with the cardboard feeding system.(when the cardboard be fed,the anilox roller is go down and touch the printing plate, when cardboard feeding is stop, the anilox roller will go up and separated from the printing plate.)
The rubber roller
The rubber roller is steel roller covered with hardwearing rubber, this roller is especially grinded, and after balance correction .the surface’s diameter in middle part of rubber roller is bigger than two sides, so as to obtain good effect of ink transmission.
The adjustment device of the printing roller.
Adopt satellite gear structure for adjust the clockwise and the anticlockwise phase of the printing roller.
The clockwise and the anticlockwise phase of the printing roller is adjusted by the PLC and electricity, Input the adjust data and 360° could be adjusted while the machine running or stop.
The horizontal move of the printing roller is adjusted by PLC with electricity; the adjusting distance is 20mm.
The “Automatic zero-returning” and “printing plate cleaned memory” function can make the machine adjust the printing plate to the right printing location quickly.
Inking system.
Inking system adopts pneumatic diaphragm pump inking with the ink cup to prevent the ink splashing. Steady inking and easy to maintain.
Have ink dust filter, make the ink more clear, and improve the printing effect.
When the machine stop, the anilox roller and rubber roller could running independently for transmission ink and prevent the ink drying out.
PLC touch screen controller on phase.
The creasing device.
Creasing wheel roller material is steel tube .
The surface of the creasing wheel roller is grinded, polished and hard chromium plating. And after balance corrective.
The distance between the up and down creasing wheel roller is adjusted by hand wheel,
while the dial show the adjust date,the adjusting scope is 2-12mm.
The slotting knife moving device
The slotting knife roller is after two times grinded.Be polished and hard chromium plating. And after balance corrective. The width of the slot is 7mm.
The slotting knife is saw-tooth, adopt alloy steel material and after heat treatment and grinded, more hardwearing and sharp-edged.
The slotting knife and creasing wheel are synchronous move left and right,for adjust the height of the carton box ,adjust by electric,with touch screen control.
The distance between the up and down slotting knife roller is adjusted by hand wheel.The up and down slotting knife plate roller adopt the crosshead connect with the drive gears,when adjust the distance between the two rollers,the distance between the two driver gears of the two rollers will not changed.
Adopt satellite gear structure for adjust the clockwise and the anticlockwise phase of the slotting knife plate.
The rubber anvil roller.
The rubber anvil roller is steel material; the surface is grinded and hard chromium plating after balance correction.
Rubber adopt fast fixing type excellent rubber. Easy to install and uninstall.
Adopting mechanical control the position move left and right of the rubber roller. The movement distance is 40mm. This structure makes the rubber covers equally wear, which can increase the use time.
The automatic Pneumatic control Up-down device of the rubber roller is synchronous with the cardboard feeding system.(when the cardboard is fed, the rubber roller is go down and cut the cardboard, when cardboard feeding is stop, the rubber roller will go up and separated from the die. )
There is a rubber repair device with the machine, the rubber can be used again after be repaired.
The die roller.
The die roller is steel material; the surface is grinded and hard chromium plating. After balance correction.
The phase adjustment of the die-cutting unit
Adopt satellite gear structure for adjust the clockwise and the anticlockwise phase of the die roller.
The clockwise and the anticlockwise phase of the die roller is adjusted by the PLC touch screen and electricity, 360° could be adjusted while the machine running or stop running.
Valid time:20 days
Payment Terms: 30% deposit by TT and 70% before shipment by TT
Guarantee: 12 months
Delivery Time: 65 working days
